This site requires JavaScript to be enabled
An updated version of this article is available

Install and Configure the Cisco AnyConnect Software VPN for Windows

106 views

31.0 - Updated on 03-21-2024 by Mike Caban

30.0 - Updated on 03-13-2024 by Mike Caban

29.0 - Updated on 03-11-2024 by Leon Lam

28.0 - Updated on 10-05-2023 by Mike Caban

27.0 - Updated on 08-03-2023 by Leon Lam

26.0 - Updated on 12-12-2022 by Paty Ruiz Gonzalez

25.0 - Updated on 12-15-2021 by Mike Caban

24.0 - Updated on 12-09-2021 by Mike Caban

23.0 - Updated on 11-01-2021 by Mike Caban

22.0 - Updated on 11-01-2021 by Mike Caban

21.0 - Updated on 11-01-2021 by Mike Caban

20.0 - Updated on 11-01-2021 by Mike Caban

19.0 - Updated on 11-01-2021 by Mike Caban

18.0 - Updated on 10-21-2021 by Mike Caban

17.0 - Updated on 10-21-2021 by Mike Caban

16.0 - Updated on 10-07-2021 by Mike Caban

15.0 - Updated on 10-07-2021 by Stephen Rico

14.0 - Updated on 07-22-2021 by Sylvia Bass

13.0 - Updated on 07-13-2021 by Mike Caban

12.0 - Updated on 07-13-2021 by Mike Caban

11.0 - Updated on 07-07-2021 by Mike Caban

10.0 - Updated on 07-07-2021 by Mike Caban

9.0 - Updated on 07-07-2021 by Mike Caban

8.0 - Updated on 06-15-2021 by Mike Caban

7.0 - Updated on 08-21-2020 by Mike Caban

6.0 - Updated on 08-21-2020 by Mike Caban

5.0 - Updated on 08-21-2020 by Mike Caban

4.0 - Updated on 07-10-2020 by Mike Caban

3.0 - Updated on 04-03-2020 by Mike Caban

2.0 - Updated on 04-02-2020 by Mike Caban

1.0 - Authored on 05-07-2015 by Mike Caban

Installing the VPN Client

  1. Download the AnyConnect VPN client for Windows. Note: If you're using Microsoft Edge, the program will download as a "sys_attachment.do" file. You will need to rename the file to "sys_attachment.msi"

  2. Click Run on the Open File – Security Warning dialog box.
  3. Click Next in the Cisco AnyConnect Secure Mobility Client Setup dialog box, then follow the steps to complete the installation. NOTE: We recommend you un-check everything (Web Security, Umbrella, etc) except for the VPN and the Diagnostic and Reporting Tool (DART). This will give you a minimal install. The other features are not supported so there's no need to install them.

Starting the VPN Client

Starting at 5pm on Monday, July 12, 2021, the process of connecting to the VPN will change slightly. After you select the Connect button, a popup window will appear where you will enter your UCInetID and password. If you are enrolled in the Duo MFA system, you will then be prompted to use Duo. Please note that due to a technical limitation, you cannot check the box labeled 'remember me for 24 hours' when using Duo with the VPN. Upon completion, you will be connected to the VPN.

  1. Go to Start->Programs->Cisco->Cisco AnyConnect Secure Mobility Client to launch the program.
  2. Enter vpn.uci.edu in the Ready to Connect to field, then press the Connect button.
  3. Select your desired connection profile from the Group drop-down menu:
    • UCIFULL – Route all traffic through the UCI VPN.
      • IMPORTANT: Use UCIFULL when accessing Library resources.
    • UCI – Route only campus traffic through the UCI VPN. All other traffic goes through your normal Internet provider.
  4. Enter your UCInetID and password, then click OK.
  5. A banner window will appear. Click Accept to close that window. You are now connected!

Disconnecting the VPN Client

When you are finished using the VPN, remember to disconnect.

  1. Right-click the AnyConnect client icon located in the system tray near the bottom right corner of your screen.
  2. Select Quit.
Revised by Mike Caban
Last modified 07-07-2021 12:49:48 PM